DESIGN AND CONSTRUCTION OF A REMOTE CONTROLLED FAN REGULATOR DESIGN AND CONSTRUCTION OF A FLOATING SWITCH

  • : Ms Word, Ms Word Format
  • : 70 Pages
  • : ₦3,000 | $25 | ₵60 | Ksh 2720
  • : 1-5 Chapters
  •  
  • Click to DOWNLOAD Materials

DESIGN AND CONSTRUCTION OF A REMOTE CONTROLLED FAN REGULATOR DESIGN AND CONSTRUCTION OF A FLOATING SWITCH

ABSTRACT

The work is on design and construction of a remote controlled fan regulator. Remote controlled fan regulator is an electronics device that enables the user to operate a fan regulator from approximately 10 meters away. However, with this device one can change the speed of the fan from your couch or bed. The device would allow a person to control the speed of a fan by simply pointing the remote towards a sensor and then pressing any key. Infrared receiver module TSOP1738 is used to receive the infrared signal transmitted by remote control.
The system was broken down into simpler functional blocks namely; infra-red transmitter, infra-red sensor, signal amplifier, control logic, sampler, control stepper, output control logic, load and display unit. Details of each subunit are described in the paper.
The system is powered by regulated 9V. The AC mains is stepped down by transformer X1 to deliver a secondary output of 12V-0-12V. The transformer output is rectified by full-wave rectifier comprising diodes D1 and D2, filtered by capacitor C9 and regulated by 7809 regulator to provide 9V regulated output.

CHAPTER ONE

    1. INTRODUCTION

Remote control facilitates the operation of fan regulators around the home or office from a distance. It provides a system that is simple to understand and also to operate, a system that would be cheap and affordable, a reliable and easy to maintain system of remote control and durable system irrespective of usage. It adds more comfort to everyday living by removing the inconvenience of having to move around to operate a fan regulator. The system seeks to develop a system that is cost effective while not under mining the need for efficiency.
1.2                                         BACKGROUND OF THE PROJECT
The first remote control, called “lazy bones” was developed in 1950 by Zenith Electronics Corporation (then known as Zenith Radio Corporation). The device was developed quickly, and it was called “Zenith space command”, the remote went into production in the fall of 1956, becoming the first practical wireless remote control device.
Remote control helps the operation of fan regulators around the home or office from a distance. It provides a system that is simple to understand and also to operate, a system that would be cheap and affordable, a reliable and easy to maintain system of remote control and durable system irrespective of usage. It adds more comfort to everyday living by removing the inconvenience of having to move around to operate a fan regulator. The system seeks to develop a system that is cost effective while not under mining the need for efficiency. Today, remote control is a standard on other consumer electronic products, including VCRs, cable and satellite boxes, digital video disc players and home audio players. And the most sophisticated TV sets have remote with as many as 50 buttons. In year 2000, more than 99 percent of all TV set and 100 percent of all VCR and DVD players sold are equipped with remote controls. The average individual these days probably picks up a remote control at least once or twice a day.
Basically, a remote control works in the following manner. A button is pressed. This completes a specific connection which produces a Morse code line signal specific to that button. The transistor amplifies the signal and sends it to the LED which translates the signal into infrared light. The sensor on the appliance detects the infrared light and reacts appropriately.
The remote control’s function is to wait for the user to press a key and then translate that into infrared light signals that are received by the receiving appliance. The carrier frequency of such infrared signals is typically around 36 kHz. Usually, the transmitter part is constructed so that the transmitter oscillator which drives the infrared transmitter LED can be turned on/off by applying a TTL (transistor-transistor logic) voltage on the modulation controlled input. On the receiver side, a photo transistor or photodiode takes up the signals.
The approach used in this work is the modular approach where the overall design was broken into functional block diagrams, where each block in the diagram represents a section of the circuit that carries out a specific function.

1.2                                        AIM/OBJECTIVE OF THE PROJECT
The aim is to design a remote control that is portable in size and a receiver that responds only to the infra-red signal transmitted by the remote control. The system responds favorable and automatically changes the fan speed. The receiver-transmitter maximum distance is approximately 10m; this is the range of the transmission of the infra-red diode used. It was noted that the receiver unit was able to receive signal propagated of the distance within the range.

1.3                                           SIGNIFICANCE OF THE STUDY
This work provides a means of control ceiling fan speed from a distance using remote. The device would allow a person to control the speed of a fan by simply pointing the remote towards a sensor and then pressing any key. Now you can lie in your bed or sit on the sofa and conveniently operate your fan. You don’t need to or have to get up. Besides, you now have extra functions that were not possible with the conventional fan regulators. It is cheap and consumes less current, this system uses from 5v to 12v dc supply while the remote uses two AAA battery.

The 5-speed ceiling fan remote control allows you stay away from your ceiling fan’s regulator and conveniently operate it. Even from a significant distance away. this fan remote control works up to a distance of 8 meters! Then think of this, especially if you use a pre-paid PHCN meter: your fans will never come on just because PHCN brought power in your absence and you had left their switches in ‘on’ position. With this control system, a fan has to be deliberately put on. It doesn’t come on just with the return of power supply. Consider how much energy you waste when fans are forgotten in ‘on’ position when power outage occurs and they just get working when power returns, often in your absence.

1.4                       PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to this study. In this chapter, the background, significance, objective limitation and problem of this study were discussed.
Chapter two is on literature review of the study. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.

Title Page———i

Certification——–ii

Dedication———iii

Acknowledgement——-iv

Abstract ———vi

Table of Content——–vii

 

Chapter One

1.0 Introduction ——-1

1.1 Statement of Problem——4

1.2 Purpose of the Study——5

1.3 Significance of Study——8

1.4 Limitation——–9

1.5 Scope of Study——-11

 

Chapter Two

2.0 Review of Related Literature —-12

2.6 Summary of Literature Review—- 19

 

Chapter Three

3.0 Research Methodology and Procedure—22

3.1 Population ——–22

3.2 Sample and Sampling Technique—-22

3.3 Validation of the Instrument —-23

3.4 Reliability of the Instrument —–23

3.5 Data Analysis——-23

Chapter Four

4.0 Presentation and Discussion of Result—24

4.1 Analysis and interpretaion of Data—25

4.2 Discussion of Results——38

 

Chapter Five

5.0. Summary, Conclusion, and Recommendation  –40

5.1 Summary——–40

5.2 Conclusion——–41

5.3 Recommendation——42

References ———45

Appendix 1——–47

Appendix ———50

DESIGN AND CONSTRUCTION OF A REMOTE CONTROLLED FAN REGULATOR DESIGN AND CONSTRUCTION OF A FLOATING SWITCH

Sharing is caring!

Leave a Reply